Home > Hard Drive > How To Install A Second Hard Drive Windows 10

How To Install A Second Hard Drive Windows 10

Contents

Makes sense, but I just didn't think about it. Computer recognizes both drives. October 23, 2009 Artem Russakovskii Full volume encryption is not a new concept - I'm using it right now. Related Articles Tips and Solutions Navigating Final Cut Pro X with the New Touch Bar-Enabled MacBook Pro by John-Paul Pales... 1 week ago 1 Tips and Solutions Ten Technical Questions http://howto301redirect.com/hard-drive/how-to-format-a-hard-drive-windows-10.html

In the article, it mentioned that the PC should not be plugged into the internet until XP SP3 is installed; they then provided the link to d/l the SP3 patch. Please advise me physical installation, formatting and set partitions to the drive. From this point I have once had Windows work sucessfully but when powered down completely the machine reverted to not seeing the hard drive in bios and only the two dvd Great step backwards MS.

How To Install A Second Hard Drive Windows 10

I didnt know many of the terms either but took a few minutes to learn what they were and then followed the clear steps to install, config and run the two Reply Alejandro says: August 3, 2008 at 8:19 pm I Have A Compaq Presario SR5130NX with a Western Digital Caviar SE (SATA) Hard Drive (Vista). If this is the case, would I simply be better off mounting it in a new external enclosure? This can be sorted out by entering the Bios when the computer boots up and looking at the boot order which should be in an Advanced or Boot menu, depending on

Some may argue that people like me who may find it easy to understand, why shouldn't the newbies? Can somebody please help. Reply Brett says: June 4, 2009 at 2:31 pm Thanks so much for this post. How To Connect Two Sata Hard Disk In One Pc Is it as simple as deleting the .vhd file?

ok the c drive does not have that much memary i took the c drive out and tryed to put a new one in but the hook ups on the drive I have to start at "start windows normally" and then tries to boot further but then blue screens and says disc drive is not configured properly. thanks, Spiv Reply israel says: March 3, 2008 at 12:59 am ------HELP PLEASE----- i am putting a unpartioned hard drive in my computer as my slave hard drive. Would this be my hard drive.

Much needed. New Hard Drive Not Showing Up Windows 10 About this wikiHow How helpful is this? Most cables are keyed to the connector so they only go in one way; if the cable isn't going in, try flipping it over. Thank you Sir.

  1. Home About wikiHow Jobs Terms of Use RSS Site map Log In Mobile view All text shared under a Creative Commons License.
  2. I pulled old IDE drive out of old box.
  3. It does the same with all three settings.
  4. I'll be back for more later.
  5. The physical installation is actually pretty easy.
  6. I only had to format the new drive.
  7. It is best to leave the case cover off for now in case you need to fiddle with something or troubleshoot the installation.
  8. You only need to worry about jumpers if you are using an IDE hard drive.

Second Hard Drive Not Showing

The IDE ribbon comes off of optical drive. reply quote 4 months agoDon Jenkins Hello Sir,I have a Toshiba  Sata HD from a HP 110-243w Desktop  running Windows 10 that the MB died. How To Install A Second Hard Drive Windows 10 Click OK again and your drive will show as “Formatting” under the Status column in Disk Management. How To Install A Second Hard Drive Windows 7 IDE drives use a wide, flat ribbon cable and may have jumpers that need to be set.

To do this, in Computer Management, right-click on your hard disk’s newly created partition and choose Change Drive Letter and Paths. http://howto301redirect.com/hard-drive/format-hard-drive-windows-xp-without-cd.html When I insert the CD on the drive I am getting a dialog box that I require 256MB memory. Reply tysun says: August 12, 2007 at 5:44 pm I install a Sata WD drive into my w2k pc. Reply Janine says: August 16, 2007 at 6:28 pm Many thanks for the VERY SIMPLE step by step instructions for initializing a STA harddrive. How To Install A Second Sata Hard Drive

Read the partition posts, and figure I would need to "ghost" the OS, or would a clean install be better and ghost the rest of the programs? I had done everything i could think of. One problem though - after setting up the new drive and using Norton Ghost 10.0 to clone the old drive, I can't boot from the new drive. http://howto301redirect.com/hard-drive/how-to-format-a-new-hard-drive-windows-10.html Diese Funktion ist zurzeit nicht verfügbar.

Can I replace it with a Seagate Momentus 7200.2 ST9200420AS 200GB 7200 RPM, which is SATA? How To Connect Two Hard Disk In One Pc How do you format a HD that you cant see then? November 7, 2010 Faye Hey guys..I'm having a problem with my window 7 VHD..

If it won't go in, make sure that the safety bump is aligned with the hole.(fig. 6) 12 Connect a Molex power cable, (a smaller connector with red, yellow, and black

Thank you for joining the B&H email list! Is there a way to access the drive without formatting?I have had to install XP on a new SATA drive and that works fine (I opted for NTSC file system)The older The first hard drive is SATA, the second which came from an older computer is IDE. How To Configure A Second Hard Drive Most IDE ribbon cables come with three connectors: one on the end (usually black) and one mid-way (usually gray), then one further away on the other end which connects to the

Cheers November 19, 2009 Jerad Hello all, I just created a virtual hard drive on my laptop but now that I have made it, I am wondering, how do I remove How I do this????? Your drive already has been seen by the computer and your just putting it inside. navigate here May be you could recommend something - Appreciate your help Alex reply quote 3 months agoGeoffrey N.

Change any necessary jumpers (see "Setting Jumpers" above) so that both drives as well as a CD drive are recognized. Risley - it's not easy finding good tech support at 10:30, but I've been waiting too long to get this up new drive up and running to wait, and this little The same thing can be done if you install a larger hard drive in your computer and don’t know what to do with the old one. One is used by my system hard drive (the drive that came with my computer), and the other is used by my SATA CD/DVD drive.

thanks Reply Andy says: August 23, 2007 at 7:22 am walter, you need to copy the drivers from the CD to a floppy and then use the floppy disk during installation That spot gets checked each time it is run from then on.